li.cil.tis3d.api.serial

Interface SerialInterface

public interface SerialInterface

Provides serial input and output on an arbitrary block position.

This is used by the serial port module to allow communication with specific blocks where a separate module might be overkill. Used for easier integration with other mods.

A serial interface always acts passively, i.e. it is always called from the serial port module, and never expected to take action autonomously (e.g. from the wrapped block's tile entity's update).

Read and write operations of the serial port module are generally uncoupled, i.e. it not being able to write to the serial interface will not cause it to block and not read from it.

Method Summary

Modifier and Type	Method and Description
boolean	canRead() Whether the interface can currently be read from.
boolean	canWrite() Whether the interface can currently be written to.
short	peek() Called to read the current value from the serial interface.
void	readFromNBT(net.minecraft.nbt.CompoundTag nbt) Called when a serial port module is created and an earlier interface had some state to save.
void	reset() Reset the state of the serial interface.
void	skip() Called to finish a read from this module.
void	write(short value) Called to write a single value to the serial interface.
void	writeToNBT(net.minecraft.nbt.CompoundTag nbt) Called when the serial port module is saved, allows storing state of the serial interface to be restored using readFromNBT(CompoundTag).

Method Detail

canWrite

boolean canWrite()

Whether the interface can currently be written to.

If this is true, the serial port module will call write(short) when it has something to write. If it is false, the serial port module won't read any values. It is legal change the returned value between ticks to cancel an active transfer.

This method is called in each update of the serial port module, which may be multiple times per tick, so this method should be decently efficient and not perform expensive computations.

Returns:

true if the interface can currently be written to.

write

void write(short value)

Called to write a single value to the serial interface.

This is only called when canWrite() is true, but when this is the case, this must not fail. If at all, the value shall be silently dropped.

Parameters:

value - the value written to the serial interface.

canRead

boolean canRead()

Whether the interface can currently be read from.

If this is true, the serial port module will call peek() to begin writing that that value to its ports. Once a write on any port completes, the serial port module will call skip() to finish the operation. It is also legal change the returned value between ticks to cancel an active transfer.

This method is called in each update of the serial port module, which may be multiple times per tick, so this method should be decently efficient and not perform expensive computations.

Returns:

true if the interface can currently be read from.

peek

short peek()

Called to read the current value from the serial interface.

This is only called when canRead() is true, but when this is the case, this must not fail.

This must not consume the current value. It is legal to change the value returned from this between ticks; the serial port module will notice this and reset any active writes.

Returns:

the current value readable from the interface.

skip

void skip()

Called to finish a read from this module.

This is only called when canRead() is true, but when this is the case, this must not fail.

reset

void reset()

Reset the state of the serial interface.

This is called when the TIS-3D computer the serial port module is part of is shut down, either regularly by the controller losing redstone power, or the casing housing the serial port module getting disconnected from its controller. This is also called when the serial port module is removed from its casing.

writeToNBT

void writeToNBT(net.minecraft.nbt.CompoundTag nbt)

Called when the serial port module is saved, allows storing state of the serial interface to be restored using readFromNBT(CompoundTag).

Parameters:

nbt - the tag to write the interface's state to.

readFromNBT

void readFromNBT(net.minecraft.nbt.CompoundTag nbt)

Called when a serial port module is created and an earlier interface had some state to save. This is usually called after the creation of the module, but in... unpredictable scenarios it might happen that this is called at a later time. In general, to play it safe, interfaces might want to add some unique identifier to their saved data, to know whether to use the data to try restoring state or not (in case the data actually belonged to another interface). Note that such incorrect assignments can typically only happen if the save-game was tampered with.

Parameters:

nbt - the tag to restore the interface's state from.